Browse by

 

The AUT Creative Industries Research Institute (CIRI) is a hub which weaves together the many creative strands running through the Faculty of Design and Creative Technologies.

  • Any use you make of these works must be for research or private study purposes only, and you may not make them available to any other person.
  • Authors control the copyright of their works. You will recognise the author’s right to be identified as the author of the work, and due acknowledgement will be made to the author where appropriate.
  • You will obtain the author’s permission before publishing any material from the work.

Recently Added

  • MIJT 2010 conference papers and proceedings [Editorial] 

    Robie, D (Pacific Media Centre, 2011)
    Conference proceedings of the Media, Investigative Journalism and Technology (MIJT) international conference at AUT University, Auckland, Aotearoa/New Zealand, on 4/5 December 2010. ISBN 978-1-877314-94-0. Published by the ...
  • Journalists at risk: news media perspectives 

    Robie, D; Edwards, B; Field, M; Bennett, C; Stephenson, J (Pacific Media Centre, AUT University, 2010)
    On May 22, 2009, Massey University’s Wellington campus hosted many speakers addressing the conference on war reporting jointly organised by the International Committee of the Red Cross. Media speakers included Television ...
  • Reinventing muckraking [Editorial] 

    Robie, D (Creative Industries Research Institute, 2011)
    Journalists need to be highly committed and determined when pursuing an issue in an investigative way because they inevitably will be confronted with considerable pressures. These pressures include resistance from publishers ...
  • Globalisation ghosts and the gatekeepers [Book Review] 

    Robie, D (Pacific Media Centre, 2011)
    A review of the second edition of the book 'Dateline Earth: Journalism as if the Planet Mattered' by Kunda Dixit is presented. Dixit argues that his provocatively titled book encourages global journalists to be 'more ...
  • Getting rid of the wires: Curved Layer Fused Deposition Modeling in Conductive Polymer Additive Manufacturing 

    Diegel, O; Singamneni, S; Huang, B; Gibson, I (Trans Tech Publications, 2011)
    This paper describes an additive manufacturing technology that has the potential to print plastic components with integral conductive polymer electronic circuits. This could have a major impact in the fields of robotics ...
  • Curved layer fused deposition modeling in conductive polymer additive manufacturing 

    Diegel, O; Singamneni, S; Huang, B; Gibson, I (Trans Tech Publications, 2011)
    This paper describes a curved-layer additive manufacturing technology that has the potential to print plastic components with integral conductive polymer electronic circuits. Researchers at AUT University in New Zealand ...
  • Evaluation of the thermal behaviour of bevelled cutting inserts using a numerical approach 

    Singamneni, SB; Singh, D; Littlefair, G; Diegel, O; Gupta, OP; Chattopadhyay, AB (Sage Publications, 2007)
    The nose geometry of a hard and brittle metal cutting tool is generally modified in order to avoid the premature failure due to fracture under tensile stresses. While most research findings point to a favourable mechanical ...
  • Computerized sales assistants: the application of computer technology to measure consumer interest - a conceptual framework 

    Shergill, GS; Sarrafzadeh, A; Diegel, O; Shekar, A (California State University, 2008)
    This paper describes a computerized intelligent sales assistant that gives sales personnel the ability to allocate their time where it will produce the best results, both for the customer, and for the business. Upon entering ...
  • Tools for sustainable product design: additive manufacturing 

    Diegel, O; Singamneni, S; Reay, S; Withell, A (Canadian Center of Science and Education, 2010)
    The advent of additive manufacturing technologies presents a number of opportunities that have the potential to greatly benefit designers, and contribute to the sustainability of products. Additive manufacturing technologies ...
  • Curved layer fused deposition modeling 

    Singamneni, S; Diegel, O; Huang, B; Gibson, I; Chowdhury, R (Sabinet, 2010)
    Current Fused Deposition Modeling (FDM) technologies deposit material as flat layers. The result is a “stair-case” effect on non-vertical or horizontal surfaces, and compromised part strength because of weakness between ...
  • A novel solution for diagnostic printing 

    Barr, K; Diegel, O; Parker, S; Henry, S (AUT University, 2011)

View more